Dual/Quad Drink Holder with Suction Cups This expandable drink holder offers a flexible solution mounting easily to most surfaces with suction cups. Expands from dual to quad holders conserving space when not in use. Accommodates drink containers up to 3-1/2" in diameter. Impact resistant injection molded nylon construction. |
Elbow Catch This spring-loaded injection molded nylon Elbow Catch is ideal for the inactive side of a pair of cabinet doors. For use on wood or metal doors where no frame is present between doors. Surface mounted. These catches are quick and simple to install and allow for door to lock shut when pushed. Requires releasing the hook to open the door, making them very secure. Traditionally used in conjunction with a touch or magnetic latch on the primary door. Latch installs with two #6 FH fasteners. Slotted hole in catch allows for adjustable installation. Installation hardware not included. |
Fillet & Prep Table Rail Mount Adapter Plate w/Hardware Fillet Table Rail Mount Adapter Plate works on the 326580-3 and 326585-3 fillet tables and comes complete with hardware to mount the plate to the table. Accepts the 327199-1 Removable Rail Mount Clamp (sold separately). |
Fillet Table Only - 20" Features:
|
Fillet Table Only - 30" Features:
|
Fillet Table Rod Holder Gimbal Mount Gimbaled Rod Holder Mounting Accessory works on all of our fillet tables (326510-3, 326515-3, 326580-3, and 326585-3) and comes complete with hardware to mount to the table. Great for mounting a variety of accessories. |
Fixed Antenna Base 4-1/4" Size with 1"-14 Thread Formed 304 Stainless Steel Fixed Antenna Base features a flange mount base. Designed to allow wire to feed directly through the base, eliminating the need for a separate cable grommet. Accepts any standard antenna with 1"-14 threads, but is ideal for TV, Loran, GPS, and VHF antennas. Constructed of corrosion resistant formed 304 stainless steel. Installs with three 1/4” RH fasteners (not included). |
Flip-Up Ladder - Single Step Flip-Up Ladder has three stationary positions. |
Flush Hatch Pull Constructed of corrosion resistant investment cast 316 stainless steel. These hatch pulls are ideal for use on doors, hatches, lazarettes, and dock boxes. Handle pivots out to open hatches and lays flush when not in use for a clean appearance. Installs with four #8 FH fasteners (not included). |
Flush Mount Rod Holder - Black Flush Mount Rod Holders are constructed of injection molded ABS. Features a 30° angle. Accommodates rods up to 1-5/8”. Installs with three #12 FH fasteners (not included). |
Flush Mount Rod Holder - White Flush Mount Rod Holders are constructed of injection molded ABS. Features a 30° angle. Accommodates rods up to 1-5/8”. Installs with three #12 FH fasteners (not included). |
Flush Mount Rod Holder with Stainless Top The look you want at an economical price! This Flush Mount Rod Holder with Stainless Top is constructed of UV resistant injection molded ABS with a stainless steel top cap. Features a 30° angle. Accommodates rods up to 1-5/8”. Installs with three #12 FH fasteners (not included). |
Fold Down All Around Light - 26" Fold Down 360° All Around Lights folds down easily for storage and comes with a white translucent lens. For replacement of existing lighting (not for new construction). Constructed of injection molded nylon and aluminum. Installs with four #10 FH fasteners (not included). 12VDC. All USCG approved navigation lights must be mounted properly to provide the correct visual alignment and allow unimpeded sight lines. Please refer to USCG regulations for 1 NM and 2 NM navigation lights for more information. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Folding Ladder - 3 Step These Portable Emergency Boarding Ladders are made of molded-in, high-visibility orange polycarbonate with nylon rope supporting the frame. They secure quickly to cleats, railings, stanchions and halyards and will support up to 300 pounds. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Folding Ladder - 4 Step These Portable Emergency Boarding Ladders are made of molded-in, high-visibility orange polycarbonate with nylon rope supporting the frame. They secure quickly to cleats, railings, stanchions and halyards and will support up to 300 pounds. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Folding Ladder - 5 Step These Portable Emergency Boarding Ladders are made of molded-in, high-visibility orange polycarbonate with nylon rope supporting the frame. They secure quickly to cleats, railings, stanchions and halyards and will support up to 300 pounds. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Folding Pole Storage Bracket These convenient pole storage brackets fold away when not in use. Constructed of corrosion resistant 304 stainless brackets with UV stabilized injection molded nylon hooks. Accepts poles up to 1-1/4” in diameter. Each bracket installs with four #12 FH fasteners (not included). WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Folding Step - Formed 304 Stainless Steel The ultimate step at a very competitive price! This Folding Step can be locked in a rattle-free, upright position when not in use. The unique design features a sawtooth, edged step to provide secure footing when working on the mast or other areas where an additional step is needed but available space is limited. Usable tread is 1” W x 4-1/4" L. Overall length is 5-5/8”. Constructed of stamped 304 stainless with a tumbled and electro-polished finish. Installs with four #10 FH fasteners (not included). |
Foot Switch Stamped 304 Stainless Steel/Rubber Cover. This Foot Switch is normally off and momentarily on when depressed by foot. Ideal for use with windlasses. Constructed of corrosion resistant stamped 304 stainless steel and rubber. Installs with ten #8 RH fasteners (not included). |
Fresh Water Inlet - 316 Stainless Steel The Fresh Water Inlet is designed to provide a fresh water hookup to a pressurized water system while moored. Standard female swivel hose connector. Comes complete with a black plastic watertight plug for use when not connected to onshore water. Pipe size: 1/2" FIPT x 3/4" FGHT. Constructed of corrosion resistant investment cast 316 stainless steel. |
Galvanized Coupler Lock Pin - 1/4" Square coupler pins add an additional level of security preventing accidental uncoupling while in transit to better protect your trailer. Electrogalvanized steel construction for corrosion resistance. The snap lock bale is spring tensioned for stronger holding power. Fits most coupler sizes. |
Galvanized Coupler Lock Pin - 5/16" Square coupler pins add an additional level of security preventing accidental uncoupling while in transit to better protect your trailer. Electrogalvanized steel construction for corrosion resistance. The snap lock bale is spring tensioned for stronger holding power. Fits most coupler sizes. |
Galvanized Prop Wrench Fits 1-1/16" Prop Nut Features:
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Galvanized Winch Cable - 3/16" x 20' Utility Snap, 155822 is rated at a 5,000 lb. breaking strength. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Hand Bilge Pump 18" x 24" These Manual Bilge Pumps are designed for use in small boats without electrical power or for larger boats in emergencies where power is no longer available. Compact, lightweight, and easy to stow. Foot valve is removable for easy cleaning. Capacities from 6-13 GPM. Pumps feature removable hoses and storage clips. To prevent leaks, hose must be screwed in, NOT pushed in. Constructed of durable UV resistant injection molded nylon. |
Hand Bilge Pump 24" x 36" These Manual Bilge Pumps are designed for use in small boats without electrical power or for larger boats in emergencies where power is no longer available. Compact, lightweight, and easy to stow. Foot valve is removable for easy cleaning. Capacities from 6-13 GPM. Pumps feature removable hoses and storage clips. To prevent leaks, hose must be screwed in, NOT pushed in. Constructed of durable UV resistant injection molded nylon. |
Hand Bilge Pump 36" x 72" These Manual Bilge Pumps are designed for use in small boats without electrical power or for larger boats in emergencies where power is no longer available. Compact, lightweight, and easy to stow. Foot valve is removable for easy cleaning. Capacities from 6-13 GPM. Pumps feature removable hoses and storage clips. To prevent leaks, hose must be screwed in, NOT pushed in. Constructed of durable UV resistant injection molded nylon. |
Hand Rail Tee 316 Stainless Steel 90° - 7/8" These Hand Rail Tee fittings create directionality in hand rail applications. Includes set screws where appropriate. Set screws can be purchased separately (299999-1). Requires 1/8" Allen wrench to install. Constructed of corrosion resistant investment cast 316 stainless steel. *Stainless tubing with a wall thickness of 0.049”. |
Hatch Adjuster - 11" Constructed of corrosion resistant formed 304 stainless steel with UV resistant injection molded nylon mounting pads and knob. These Hatch Adjusters feature a simple thumb screw knob to lock into position. Great for dock box lids, hatches, windshields, etc. |
Hatch Adjuster - 14" Constructed of corrosion resistant formed 304 stainless steel with UV resistant injection molded nylon mounting pads and knob. These Hatch Adjusters feature a simple thumb screw knob to lock into position. Great for dock box lids, hatches, windshields, etc. |
Hatch Cover Pull & Gasket Highly corrosion resistant, this Hatch Cover Pull provides a simple and convenient way to open the hatches in your boat. Easy-to-install, it features a stainless steel washer for a tight and secure fit, and a rubber gasket to reduce noise and resist water penetration. Commonly used on deck mounted access hatches, this hatch cover pull not only looks attractive, but is durable for use in harsh marine conditions. Requires a 3/16” hole. Flange pull is 1-1/4” in diameter x 1/8” thick. |
Hatch Handle Latch - 3-1/8" x 2-11/16" Constructed of sand cast brass with a chrome plated finish. These Hatch Handle Latches are ideal for use on doors, hatches, lazarettes, and dock boxes. Handle pivots out to open hatches and lays flush when not in use for a clean appearance. Adjustable locking arm adds additional security. Installs with four #8 FH fasteners (not included). Once installed, the locking arm can be trimmed to length. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
|
|
|
|
Copyright © 2009-2024 A part of the Intelastores, Inc. Store Network Site Designed and Maintained by Inline Internet Systems, Inc. |