Dress White 4" Tachometer w/Systemcheck Indicator - 7,000 RPM (Gas - Johnson / Evinrude Outboard) Perimeter-lighted White dial with bold black graphics, white aluminum bezel, contoured black pointer, and flat glass lens. Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed. By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution. These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine. SystemCheck® warnings
4" - Hole size: 3.375" (85mm) Specifications:
Factory P/N TC9887 |
Dress White Boxed Set - Inboard Motors Perimeter-lighted White dial with bold black graphics, white aluminum bezel, contoured black pointer, and flat glass lens. Packaged and ready for the display counter. This 6 Gauge Boxed Sets offers a complete set of gauges ready to install. Inboard Motors Boxed Set Includes
Factory P/N KT9797 |
Dress White Boxed Set - Outboard Motors Perimeter-lighted White dial with bold black graphics, white aluminum bezel, contoured black pointer, and flat glass lens. Packaged and ready for the display counter. This 4 Gauge Boxed Set offers a complete set of gauges ready to install. Outboard Motors Boxed Set Includes
Factory P/N KT9794 |
Euro 4" Tachometer with Hourmeter (4000 RPM) (Diesel) (Mech Takeoff & Var Ratio Alt) Perimeter-lighted black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Electronic tachometers work by counting pulses generated by the ingition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed above. By selecting the right tach and setting the switch on the back to the correct postion you let the tachometer know how many pulses are sent per each engine revolution. Benefits:
|
Euro Black 2" Ammeter Gauge (60-0-60 Amps) Faria Euro Black gauges feature perimeter-lighted black dial with bold White graphics, Black aluminum bezel, contoured White pointer, and flat glass lens. An ammeter indicates the current flow through the battery charging system. A "zero center" ammeter, during chargine, shows a (+) positive reading indicating the current is flowing to the battery (charge). A (-) negative reading indicates current flowing away from the battery (discharge.) 2" - Hole size: 2.0625" (53mm) Specifications:
Factory P/N AP9523 |
Euro Black 2" Depth Sounder with In-Hull Transducer Perimeter-lighted black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. The Depth Sounders from Faria offer a 3-199 foot (1-61 meters) depth capability, with an automatic gain control, backlighting for maximum night vision, keel offset, and deep and shallow water alarms. Depth can be read in meters, and feet. With its oversized back-lit display depth can be easily read in any condition. Audible and Visual alarms let the boater know when a shallow or deep water condition exists. Depth Sounder includes a Faria SN2010 In-hull transducer w/20' cable. 2" - Hole Size: 2.0625" (53mm) Specifications:
Factory P/N DS0101 |
Euro Black 2" Depth Sounder w/Transom Mount Transducer Perimeter-lighted black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. The Depth Sounders from Faria offer a 3-199 foot (1-61meters) depth capability, with an automatic gain control, backlighting for maximum night vision, keel offset, and deep and shallow water alarms. Depth can be read in meters, and feet. With its oversized back-lit display depth can be easily read in any condition. Audible and Visual alarms let the boater know when a shallow or deep water condition exists. Depth Sounder includes a Faria SN2010 In-Hull Transducer w/20' cable. 2" - Hole Size: 2.0625" (53mm) Specifications:
Factory P/N DS0101 |
Euro Black 2" Fuel Level Gauge (E-1/2-F) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Fuel Level gauge operates by sending a low amperage current through the gauges meter to ground via a sending unit with variable resistance. The resistance of the sending units increase or decrease with the changes in pressure, temperature, etc... As the sender's resistance varies, the amount of current allowed to flow through it to ground changes and the meter deflects, showing the level of fuel. 2" - Hole Size: 2.0625" (53mm) Specifications:
Factory P/N GP9357 |
Euro Black 2" Oil Pressure Gauge (80 PSI) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. A pressure gauge operates by sending a low amperage current through the gauge's meter to ground via a sending unit with variable resistance. The resistance of the sending units increase or decrease with the changes in pressure, temperature, etc... As the sender's resistance varies, the amount of current allowed to flow through it to ground changes and the meter deflects, showing the change in pressure. 2" - Hole size: 2.0625" (53mm) Specifications:
Factory P/N GP9599 |
Euro Black 2" Trim Gauge (Johnson/Evinrude/Suzuki Outboard) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. 2"- Hole Size: 2.0625" (53mm) For Engine Types:
Specifications:
Factory P/N GP9305 |
Euro Black 2" Trim Gauge (Mercury/Mariner/Mercruiser/Volvo DP/Yamaha-2001 and newer) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens.2"- Hole Size: 2.0625" (53mm) For Engine Types:
Specifications:
Factory P/N GP9374 |
Euro Black 2" Voltmeter (10-16 VDC) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. A voltmeter indicates the battery voltage and the general condition of the battery charging system. The meter requires no warm-up and indicates voltage changes instantly. 2" - Hole Size: 2.0625" (53mm) Specifications:
Factory P/N VP9134 |
Euro Black 2" Water Temperature Gauge (100-250°F) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. A temperature gauge operates by sending a low amperage current through the gauges meter to ground via a sending unit with variable resistance. The resistance of the sending units increase or decrease with the changes in pressure, temperature, etc... As the sender's resistance varies, the amount of current allowed to flow through it to ground changes and the meter deflects, showing the temperature. 2" - Hole Size: 2.0625" (53mm) Specifications:
Factory P/N GP9118 |
Euro Black 4" 30 Knot Speedometer for Mechanical Pitot Tube The Faria Beede Euro Black style speedometer gauge features a black aluminum bezel, black dial, white pointer and graphics displaying speed, with perimeter back lighting and a flat glass lens. The Faria Beede speedometer gauge is for use with a mechanical pitot tube sender to gauge the speed of your boat. The sensor drops into the water off the back of the boat and receives different levels of pressure depending on the speed the boat is travelling through the water. This pressure equates to a reading in the dashboard mounted speedometer. This speedometer measures up to 30 knots. 4" Gauge - Hole size: 3.4" (86.36 mm) Features:
Factory P/N SE9659 |
Euro Black 4" Speedometer - 55MPH (Mechanical) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Electronic speedometers operate by capturing pulses produced by a sensor. the pulses are then electronically converted to a speed reading very much like a tachometer converts ignition pulses to RPM. Pitot tube type speedometers operate by pressure from the water being forced into the pitot tube. This pressure is then transmitted through flexible tubing to the bourdon tube movement inside the speedometer head where it is converted into a speed reading by the movement mechanism. ∗ Pitot tube sold separately. 4" - Hole Size: 3.375" (85mm) Specifications:
Factory P/N SE9463 |
Euro Black 4" Speedometer - 80MPH (Mechanical) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Electronic speedometers operate by capturing pulses produced by a sensor. the pulses are then electronically converted to a speed reading very much like a tachometer converts ignition pulses to RPM. Pitot tube type speedometers operate by pressure from the water being forced into the pitot tube. This pressure is then transmitted through flexible tubing to the bourdon tube movement inside the speedometer head where it is converted into a speed reading by the movement mechanism. ∗ Pitot tube sold separately. 4" - Hole Size: 3.375" (85mm) Specifications:
Factory P/N SE9460 |
Euro Black 4" Speedometer 60MPH -GPS 4" - Hole Size: 3.375" (85mm) A drop in replacement for your current speedometer to match your existing instrument dash.GPS information is gathered from an internal GPS antenna. No external antenna required. The GPS Speedometer uses a highly accurate 48 channel GPS receiver. Speed data is shown by an analog pointer. This pointer is driven by a digital stepper motor for increased accuracy and minimized pointer bounce during vessel operation. Euro Black Series features perimeter-lighted black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Deutsch Connectorized harness is intended to fit directly into today's dash harnesses with easy Plug and Play connectors.Studded harness is designed to fit into existing dash harnesses all ready installed. The studded speedometer connects directly to the battery and ground without the addition of a costly connector. |
Euro Black 4" Tachometer - 4,000 RPM (Diesel - Magnetic Pick-Up) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed. By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution. 4" - Hole size: 3.375" (85mm) Specifications:
Factory P/N TC9671 |
Euro Black 4" Tachometer - 4,000 RPM (Diesel - Mechanical Takeoff & Var Ratio Alt) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed. By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution. 4" - Hole size: 3.375" (85mm) Specifications:
Factory P/N TD9122 |
Euro Black 4" Tachometer - 6,000 RPM (Gas - Inboard & I/O) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed. By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution. 4" - Hole size: 3.375" (85mm) Specifications:
Factory P/N TC9643 |
Euro Black 4" Tachometer - 7,000 RPM (Gas - All Outboard) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed. By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution. 4" - Hole size: 3.375" (85mm) Specifications:
Factory P/N TC9011 |
Euro Black 4" Tachometer with Hourmeter - 6,000 RPM (Gas - Inboard) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed. By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution. 4" - Hole size: 3.375" (85mm) Specifications:
Technical Specifications:
Factory P/N TC9122 |
Euro Black 4" Tachometer with Hourmeter - 7,000 RPM (Gas - Outboard) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed. By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution. 4" - Hole size: 3.375" (85mm) Specifications:
Technical Specifications:
Factory P/N TCH015 |
Euro Black 4" Tachometer w/Systemcheck Indicator - 7,000 RPM (Gas - Johnson / Evinrude Outboard) Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed. By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution. These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine. SystemCheck® Warnings:
4" - Hole size: 3.375" (85mm) Specifications:
Factory P/N TC9951 |
Euro Black Boxed Set - Inboard Motors Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Packaged and ready for the display counter. This 6 Gauge Boxed Sets offer a complete set of gauges ready to install. Inboard Motors Boxed Set Includes:
Factory P/N KTF9799 |
Euro Black Boxed Set - Outboard Motors Perimeter-lighted Black dial with bold white graphics, black aluminum bezel, contoured white pointer, and flat glass lens. Packaged and ready for the display counter. This 4 Gauge Boxed Set offers a complete set of gauges ready to install. Outboard Motors Boxed Set Includes:
Factory P/N KT9796 |
Euro White 2" Fuel Level Gauge (E-1/2-F)
2" - Hole Size: 2.0625" (53mm) Fuel Level gauge operates by sending a low amperage current through the gauges's meter to ground via a sending unit with variable resistance. The resistance of the sending units increase or decrease with the changes in pressure, temperature, etc... As the sender's resistance varies, the amount of current allowed to flow through it to ground changes and the meter deflects, showing the level of fuel. |
2" Hourmeter (10,000 Hrs) (12-32 VDC) - Euro White
2" - Hole size: 2.0625" (53mm) Hourmeter operates by applying battery voltage across the gauges's register motor to ground. The register increments increase when the key switch in on. Route power through a normally open Oil Pressure switch to count "engine running" hours. Benefits:
|
Euro White 2" Oil Pressure Gauge - 80 PSI
2" - Hole size: 2.0625" (53mm) A pressure gauge operates by sending a low amperage current through the gauges's meter to ground via a sending unit with variable resistance. The resistance of the sending units increase or decrease with the changes in pressure, temperature, etc... As the sender's resistance varies, the amount of current allowed to flow through it to ground changes and the meter deflects, showing the change in pressure. Benefits:
|
2" Trim Gauge (J/E/Suzuki Outboard)
2"- Hole Size: 2.0625" (53mm) For Engine Types:
|
Euro White 2" Trim Gauge (Mercury/Mariner/Mercruiser/Volvo DP/Yamaha-2001 and newer)
2"- Hole Size: 2.0625" (53mm) For Engine Types:
|
Euro White 2" Voltmeter (10-16 VDC)
2" - Hole Size: 2.0625" (53mm) A voltmeter indicates the battery voltage and the general condition of the battery charging system. The meter requires no warm-up and indicates voltage changes instantly. |
|
|
|
|
Copyright © 2009-2024 A part of the Intelastores, Inc. Store Network Site Designed and Maintained by Inline Internet Systems, Inc. |