Shop by Brand: Edson Marine

Stainless Replacement Brake Knob

Edson’s Stainless Replacement Brake Knob can be easily retrofitted onto your older Edson Pedestal with side-mount brake. Easy press-on installation requires no tools.

NOT FOR THROUGH SHAFT WHEEL BRAKES.

Stainless Steel Pedestal Guard Mounting Feet - Pair

Edson Pedestal Guard Mounting Feet are available in pairs as a direct replacement for Edson’s black plastic feet. Gasket and bushing allow for mounting 1”, 1-1/8” or 1-1/4” guard pipes. Nuts and washers included.

Stainless Steel Wheel Nut - 1"-14 Shaft Threads

Attention to detail is the keynote of these Edson Wheel Nuts. Highly polished Investment Cast 316 Stainless has superior strength as well as good looks. Measure your steering shaft thread for the correct size.

Features:

• 1-inch - 14 Shaft Threads.
• Fits Edson Pedestal Shafts built between 1979 to 1999.
• Cast 316 Stainless Steel.
• Polished to a mirror finish

Stainless Throttle Handle

Upgrade your older Edson controls with these stainless replacements. Highly polished, marked “Fast-Slow”. Can be easily retrofitted onto existing Edson engine controls. Includes mounting screw.

IMPORTANT: These handles are only for Edson's Dual Lever Engine Controls. Older pedestals (pre-1980) with 10-32 set screw threads must be retapped to 1/4"-28 in order to accept the mounting screws supplied with these handles. 

Superlube® Conduit & Bearing Lubicrant - 14oz

Superlube® is a Teflon® grease for use in all Edson Systems. Ideal for both conduit and needle bearing use

The Vision Series Mounting System is a revolutionary design that provides the simplest, most attractive solution to your electronics mounting requirements.

Features:

• All-new sleek, modern design
• First all modular system - extremely versatile
• Simple selection and installation
• Easy to add accessories
• Powder coated aluminum
• Requires Vision Mounting Plate to install radar or sat dome antenna

6" Aft Angled Mount

• 6" tall
• Aft Raked 30 degrees

Attwood LED 12V Combination Anchor/Streaming Light

Edson offers the 67510 Attwood LED Anchor/Steaming Light (72" Wire Length) that is specifically designed for Edson's Vision Series Light Arms. With 3NM of 360° visibility while drawing a fraction of the power of traditional incandescent lights, Attwood's 3NM LED Masthead/Anchor light is one of the first of its kind. Constructed of corrosion resistant composites with stainless steel accents, this product was designed for the harsh coastal marine environment. For use on boats up to 65.6 ft. (20 meters)

The 67510 Attwood LED Anchor/Steaming Light requires an Edson Light Arm that is secured to a Vision Series Base Mount with a Light Arm Receiver and Radar Mounting Plate. Order Edson's Light Arm, Light Arm Receiver,  Base Mount and Mounting Plate separately.

GPS Mount with Light Extension Adapter

Edson's 67400 GPS Mount with Light Extension Adapter is specifically designed for Edson's Vision Series Light Arms. The  powder coated stainless steel GPS Mount allows you to add a GPS antenna to your Light Arm. The GPS Mount also has an extension to attach your navigation anchor/steaming light. 

*Shown with optional Perko Anchor/Steaming Light. Must be ordered separately.*

The 67400 GPS Mount with Light Extension Adapter requires an Edson Light Arm that is secured to a Vision Series Base Mount with a Light Arm Receiver and Radar Mounting Plate. Order Edson's Light Arm, Light Arm Receiver,  Base Mount and Mounting Plate separately.

Light Arm for Open Array Radars

Edson's 68660 Vision Series Light Arm allows you to attach your Navigation Light to your Edson Vision Series Mount with a Open Array Radar.

Light Arm extends 28" toward the stern allowing room for your Radar or Satellite Dome. The Light Arm is 28" tall, which meets Coast Guard standards for navigation lights.

Edson's Light Arm requires a Light Arm Receiver that is dependent on the style of Vision Series Mount you have (Aft Angled or Vertical). 

Specifications:

Mounting Plates and Light Arm Receiver are required to complete an Edson Vision Series Mounting System. (sold separately)

Base mounts sold separately

Light Arm for Radar Domes and Sat Domes

Edson's 68650 Vision Series Light Arm allows you to attach your Navigation Light to your Edson Vision Series Mount with a Radar Dome and Satellite Dome. 

Light Arm extends 14" toward the stern allowing room for your Radar or Satellite Dome. The Light Arm is 28" tall, which meets Coast Guard standards for navigation lights.

Edson's Light Arm requires a Light Arm Receiver that is dependent on the style of Vision Series Mount you have (Aft Angled or Vertical). 

Specifications:

Mounting Plates and Light Arm Receiver are required to complete an Edson Vision Series Mounting System. (sold separately)

Base mounts sold separately

Light Arm Receiver for Aft Angled Mounts

The Light Arm Receiver secures a Light Arm to the mounting plate on Edson Vision Series Aft Angle Mounts. Edson's Light Arm Receivers require an Edson Mounting Plate and an Edson Vision Series Mount.

Specifications:

Mounting Plates are required to complete an Edson Vision Series Mounting System. 

Base mounts sold separately

Garmin Mounting Plate for 18" & 24" HD, xHD, HD+ 4kW Radar domes

With Edson's Vision Series Mounting System, you can select your desired Mounting Plate to best fit your electronics. Edson's 68520 Vision Series Mounting Plate is designed for Garmin 18 and 24 Radar Domes (GMR Fantom 18, GMR Fantom 24, GMR 18 HD+, GMR 18 xHD, & GRM 24 xHD). 

Specifications:

Mounting Plates are required to complete an Edson Vision Series Mounting System. 

Base mounts sold separately

Intellian/KVH/Cobham Mounting Plate

With Edson's Vision Series Mounting System, you can select your desired Mounting Plate to best fit your electronics. Edson's 68720 Vision Series Mounting Plate is designed for Intellian FB150 & FB250, KVH TracPhone Fleet One FB150 & FB250, and Cobham Sailor FB150 & FB250.

Specifications:

Mounting Plates are required to complete an Edson Vision Series Mounting System. 

Base mounts sold separately

Intellian/KVH/Raymarine/Sea King/SeaTel Mounting Plate

With Edson's Vision Series Mounting System, you can select your desired Mounting Plate to best fit your electronics. Edson's 68600 Vision Series Mounting Plate is designed for Raymarine 33STV & 37STV , Sea-King 15, SeaTel C14, Intellian i1, i2, &i3, and KVH M1, M2, M3, V3, TV1, TV3.

Specifications:

Mounting Plates are required to complete an Edson Vision Series Mounting System. 

Base mounts sold separately

Simrad/Lowrance/ B&G 2kW & 4G Radar Domes Mounting Plate

With Edson's Vision Series Mounting System, you can select your desired Mounting Plate to best fit your electronics. Edson's 68530 Vision Series Mounting Plate is designed for Simrad, Northstar, B&G, & Lowrance 2kW, HD, 3G, & 4G Radar Domes (LRA-1800, NS007001, DX42S-1). 

Specifications:

Mounting Plates are required to complete an Edson Vision Series Mounting System. 

Base mounts sold separately

Simrad/ B&G/ Lowrance 4KW Radar Dome Mounting Plate

With Edson's Vision Series Mounting System, you can select your desired Mounting Plate to best fit your electronics. Edson's 68540 Vision Series Mounting Plate is designed for Simrad, Northstar, B&G, & Lowrance 4kW, HD, 3G, & 4G Radar Domes (LRA-2400, NS007002, DX64S-1). 

Specifications:

Mounting Plates are required to complete an Edson Vision Series Mounting System. 

Base mounts sold separately

Vision Series Mounting Plate f/Raymarine Quantum, 2kW & 4kW Radar Domes

With Edson's Vision Series Mounting System, you can select your desired Mounting Plate to best fit your electronics. Edson's 68551 Vision Series Mounting Plate is designed for Raymarine Radar Domes (Quantum, Quantum 2, RD418D, RD424D, RD418HD, RD424HD). Mounting Plates are required to complete an Edson Vision Series Mounting System.

Base mount sold separately. 

Perko Combination Anchor/Steaming Light (50" Wire Length)

Edson offers the 67500 Perko Combination Anchor/Steaming Light (50" Wire Length) that is specifically designed for Edson's Vision Series Light Arms. All-Round White Light with 12 volt bulb and is constructed of Black Polymer and Chrome Plated Zinc Alloy Top.

 Certified For Use on Sail or Power Driven Vessels Under 20 Meters (65.6 ft.) in Length

The 67500 Perko Combination Anchor/Steaming Light requires an Edson Light Arm that is secured to a Vision Series Base Mount with a Light Arm Receiver and Radar Mounting Plate. Order Edson's Light Arm, Light Arm Receiver,  Base Mount and Mounting Plate separately.

Vision Series Univeral Mounting Plate - 10-5/8" Diameter with No Holes

With Edson's Vision Series Mounting System, you can select your desired Mounting Plate to best fit your electronics. Edson's Vision Series Universal Mounting Plate is 10-5/8" diameter without pre-drilled holes. You drill your own holes to fit any antenna or dome.

Mounting Plates are required to complete an Edson Vision Series Mounting Series.

Order Base Mount separately.

Vision Series Universal Mounting Plate - 15" Diameter with No Holes

With Edson's Vision Series Mounting System, you can select your desired Mounting Plate to best fit your electronics. Edson's Vision Series Universal Mounting Plate is 15" diameter without pre-drilled holes. You drill your own holes to fit any antenna or dome.

Specifications:

Mounting Plates are required to complete an Edson Vision Series Mounting System. 

Base mounts sold separately