10M VCAN Bus Cable Controller to Hub Features:
|
20M VCAN BUS Cable Hub to Thruster Features:
|
Adapter Plate to Replace BPS/BPJ Panels with BPSE/BPJE Panels Adapter plate for use when replacing old BPS/BPJ panels with updated BPSE/BPJE type panels. The updated panels are 85mm x 85mm, whereas the old style panels measured 98mm x 98mm. |
Bow & Stern Thruster Easy Docking Panel - 12/24V
This control panel combines the functions of twin joysticks into one easy to operate knob. The simple and intuitive control action ensures that operation of both bow and stern thruster together becomes a smooth procedure. The use of Hall effect sensors in this control panel means there are no holes in it and it is therefore completely watertight to IP 67. Features:
|
BOW PRO 571 Bow Thruster 57KGF - 12V The BOW PRO thrusters are fitted with proven induction technology. This system makes the use of carbon brushes obsolete. As a result, the bow thruster is very quiet and has indefinite* run-time! The (AC) induction motor is controlled by the VETUS MCV motor controller. This in-house-engineered motor controller can handle both 12V, 24V and AC motors, making the new bow thruster suitable for almost all boats! The BOW PRO thruster is controlled by a proprietary CANBUS protocol. There are two different panels available for this thruster; one fully-proportional basic panel and one fully-proportional panel with lock-function. This allows the boat to be moored without the use of ropes. Letting passengers board your vessel have never been this easy! Evolution is to continue on a set of good properties, so there are similarities with its predecessors: remained are the very silent propeller blades and the streamlined tailpiece. Retrofitting a BOW PRO thruster, therefore, is a piece of cake as the new motor is interchangeable with the tailpiece and flange of our thruster range. Features:
|
Bow Thruster - 55 kgf - 12V
The Vetus 55 kgf is arguably the most popular bow thruster for yachts and powerboats from 28 to 41 feet in length. Manufactured using the highest quality materials to give high power and long service life. The Vetus 55 kgf unit is one of the few thrusters for this class of vessel with a 150mm diameter tunnel - making it much easier to fit than competitors with standard 185mm units. Features:
|
Bow Thruster Extension Cable - 20'
Connection cable 20' for use with Vetus thruster control panels. |
Bow Thruster Extension Cable - 53'
Connection cable 53' for use with Vetus thruster control panels. |
Bow Thruster Panel w/Buttons & Time Lapse
Single touch panel for operating a Vetus bow or stern thruster. Supplied with quick connectors for BP29 series wiring harnesses. Capable of daisy chaining additional controls for multiple stations. Features:
|
Bow Thruster Panel w/Joystick & Time Lapse
Single joystick panel for operating a Vetus bow or stern thruster. Supplied with quick connectors for BP29 series wiring harnesses. Capable of daisy chaining additional controls for multiple stations. Features:
|
CAN 3 Point Hub for Swing & Bow Pro Thruster CAN-bus 3 point hub. |
CAN Terminating Resistor V2 The VETUS CAN Terminating Resistor V2 provides durable marine-grade construction and design, for use in terminating one end of your CAN Bus Network. |
Drainplug for Waterlock ACC Tank The DRAIN is the plug that closes the drainhole on waterlocks and accumulator tanks. |
Drive Pin Set for BOW 50/60/75/80/95 Replacement Stainless Drive pin for the VETUS BOW 50/60/75/80/95 (5x27.5mm) propeller shaft. |
Drive Pin Set for Vetus Bow 35 & 55kgf - 5-Pack Replacement Drive Pin (5 pieces) for the Vetus Bow 35 and 55kgf Thrusters (5X45,5Mm). |
Fuse Holder C100
Fuse holder, type C100 including cover, suitable for fuses of 40 to 500 amp |
Fuse Strip C20 - 160 Amp Features:
|
Fuse Strip C20 - 300 Amp Features:
|
Fuse Strip C20 - 500 Amp Features:
|
Fuse Strip C30 - 125 Amp Features:
|
Fuse Strip C30 - 50 Amp Features:
|
Fuse Trip C20 - 250A
Strip Fuse C20 - 250 amp |
Fuseholder Specifically for VETUS fuses |
Gasket & Seal Set for Helm Pumps MT30-MT140 Full service kit for VETUS Helm Pumps MT40 to MT140 (including the more recent MTP42, MTP53) Consists of shaft seal (HS801 25 x 42 x 7mm) and back plate gasket (HS804). |
Gasket Tailpiece - 2mm Features:
|
Joystick with Hold VETUS Bow Pro Proportional Joystick control panel. Features:
Designed for use with the VETUS Bow Pro thrusters only - not suitable for standard DC Thrusters. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. |
Neutral Button Kit for SICO & SISCO Features:
|
O-Ring & Cover for Waterfilter 1320 Replacement lid (Cover) and O Ring kit for the VETUS FTR1320 series raw water strainer units. Fits all sizes from 38 to 51mm. |
O-Ring D 48 x 3mm NBR 70 Shore O-Ring for Vetus mufflers, waterlocks and gas/water separators. Specifications:
Fits: NLP40, NLPH40, NLPG40, WLOCK40R, LSS40A and LGS4038 NLP45, NLPH45, NLPG45, WLOCK45R, LSS45A and LGS4538 NLP50, NLPH50, NLPG50, WLOCK50R, LSS50A and LGS5038 |
O-Ring Set for Waterfilter 1320 - 5-Pack This set contains the O-ring (5x) for the FTR1320 Waterfilter |
Propeller for BOW125/130/160 Propeller 6 blade, diameter 246mm, for 125/130/160 kgf bow thrusters. Set includes all mounting hardware for propeller. Working in close collaboration with the Maritime Institute Netherlands (MARIN), the world-famous hydrodynamic laboratory, VETUS has optimized the performance of its thrusters. This has been achieved by utilizing a unique propeller blade profile, which creates little or no cavitation. As cavitation produces unwanted noise, this new blade design offers a major reduction in the operating sound levels for VETUS bow thrusters. Moreover, the application of this propeller has reduced the current consumption by up to 10%. *Zinc sold separately. |
Replacement O-Rings Set - 5-Pack Set of 5 O replacement Ring seals for Vetus FTR330 Series Raw Water Strainers. |
|
|
|
|
Copyright © 2009-2024 A part of the Intelastores, Inc. Store Network Site Designed and Maintained by Inline Internet Systems, Inc. |