Shop by Brand: BEP Marine

24-Hour Essential Circuits Module
1 x 5A

The 706-4W 24hr service module consists of 1 x 5amp and 3 x 15amp push to reset Carling CLB Series thermal circuit breakers. Suitable for essential circuits such as bilge pump auto float switch supplies and stereo memory circuits. The push to reset function ensures essential 24hr circuits cannot be switched off inadvertently. This is contained in the contour lock double module.

• Consists of one 5A and three 15A push to reset Carling CLB Series thermal CBs
  
• The push to reset function ensures essential 24hr circuits cannot be switched off inadvertently

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

65A PVC Coated Continuous Duty Solenoid

Remotely switch high amperage loads with a low amperage on-off switch.

Features:

• Continuous duty, 65A at 12V DC
• Intermittent rating 100A: 10 seconds
• Copper #10-32 thread signal terminals
• Copper 5/16”-24 thread contact terminals
• PVC coated steel case
• Bracket mounting holes 5/16” x 19/32”, 2-13/64” on centers
• UL and CE approved
• Same as Cole Hersee part number 24117-01

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

85A Remote Switching Continuous Duty Solenoid

Can be used with Electro-Scan MSDs and other high-amp circuits with remote operation.

Features:

• Continuous duty, 85A at 12V DC
• Intermittent rating 750A make/100A break, 10 seconds On, 30 minutes Off
• Insulated ground
• Steel housing, brass hardware
• UL listed and CE certified
• Same as Cole Hersee part number 24059

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ATC Six Way Bus Bar with 5mm Input Stud

The ATC Negative Bus uses the BEP Contour lock system to allow it to be joined to the ATC fuse holder. This keeps wiring tidy and conveniently located. Current Rating: 100Amps.

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Battery Control Center for Triple Engine Remote

Reliable automation is key when installing a sophisticated electrical system. BEP's Battery Control Center (BCC) is an advanced line of rugged remote operated switching banks that deliver hard-handling and good-looking power management where it's needed. The BCC is equipped with locks on each battery switch position to ensure group operation at the turn of a key. Any switch can be isolated by disengaging its lock and toggling the switch off.

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Battery Distribution Cluster f/Twin Outboard Engine w/Three Battery Banks


The 717-140A-DVSR is designed for twin engine installations. It allows the port engine to charge both the port start battery and the house battery when the port VSR is engaged. It also allows the starboard engine to charge both the starboard start battery and the house battery when the starboard VSR is engaged. This gives you a combined charge from two engines into the house battery until the voltage regulators on both engines control the charge. It also allows you to charge the house battery if steaming on one engine.

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Mini Contour Battery Disconnect Switch - 275A Continuous

This switch offers a number of unique features, the highlight being the Contour Locking System, allowing it to be a stand alone unit, or locked together with other switches. The control knob can be removed by switching to an counterclockwise 45 degree position. This control knob also features an interchangeable labeling system allowing a full range of applications (Item # 713 or 715). Three removable side plates provide access of up to 1/0 cables. The rear cover insulating the rear terminals against any short circuits. This ensures that the switch meets ABYC requirements. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100°C (212°F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory.

Features:

• Can be either surface or recess mounted by cutting a 2.1" (52 mm) hole
  
• Available with house knob (OEM # 701B-HB) or with chassis knob (OEM # 701B-CH)
  
• Tin-plated copper studs and nuts
  
• Ignition-protected

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Contura Double Switch Mounting Bracket

Two middle sections. Modular design permits assembly in groups - can be used with part number 1001701 or 1001703.

Features:

• Used with Rocker Switches and Contoura Switches
• Same as Cole Hersee part number 82159-03

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Contura Single Switch Mounting Bracket

One end section. Modular design permits assembly in groups - can be used with part number 1001702.

Features:

• Used with Rocker Switches and Contoura Switches
• Same as Cole Hersee part number 82159-1

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Digtal Voltage Sensing Relay (DVSR) - 12/24V

The Digital Voltage Sensing Relay (DVSR) allows the charging of a second battery bank from any single charging source. When the voltage on the charged bank rises sufficiently, the DVSR engages allowing the 2nd battery bank to charge. When charging stops and voltage falls, the DVSR automatically isolates the battery banks, ensuring that engine start batteries are kept fully charged. Digital circuitry provides superior reliability and extremely low power consumption. Digital enhancements have introduced remote sensing circuitry that allows an optional connection from the ignition switch to provide the same functionality as single sense VSR and zero power consumption when engine is off. Another benefit is a zero stand by current draw when remote sensing circuit is utilized with a storage mode switch fitted (switch in open position).

Features:

• Safely charge two or more independent battery banks from one charge source such as an alternator or battery charger
  
• Charges engine starting batteries before combining auxiliary bank for charging
  
• Protects start batteries from becoming flattened by domestic loads
  
• Isolates electronics from harmful electrical surges from starter motors
  
• Simple to install 3 wire connection leaves alternator wiring intact
  
• No volt drop vs diode isolators
  
• Ignition protected
  
• Surface or panel mountable
  
• Replaces previous models 710-125A and 710-125A-DS
  
• Multi voltage, auto selects between 12 and 24V DC operation
  
• Digital circuits provide very low power consumption and enhanced performance
  
• Remote status LED output option
  

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Dual Operation VSS Switch 12/24V HD Optic - 500A

These Voltage Sensitive Switches (VSS) automatically sense connected battery bank voltages and provide optimal, efficient charging of the second bank. The VSS allows for independent battery banks to be combined or isolated based on the presence of a charging source (such as an engine alternator or battery charger), while also offering remotely activated, high current, emergency parallel connection. Designed and constructed for longevity in the marine environment with tinned copper conductors, stainless steel nuts, and high temperature, fibre reinforced plastics. The units are ignition protected, provide On/Off switching operation, and may be recessed or surface mounted. The remote emergency parallel function can be operated through a momentary button on the dash which will parallel the batteries for 10 minutes. Once this 10 minutes has passed, if the voltage is high enough, the voltage sensitive switch will stay engaged. If not, it will disengage.

Features:

• Dual battery sensing
  
• Manual override option
  
• Dual 12/24 volt operation (both banks must be same voltage)
  
• Low power consumption (<6mA)
  
• Lowered cut in voltage (13.3/26.6V) suits low output alternators and high temperature environments

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Dual Operation VSS Switch 275A Cont Motorized

These Voltage Sensitive Switches (VSS) automatically sense connected battery bank voltages and provide optimal, efficient charging of the second bank. The VSS allows for independent battery banks to be combined or isolated based on the presence of a charging source (such as an engine alternator or battery charger), while also offering remotely activated, high current, emergency parallel connection. Designed and constructed for longevity in the marine environment with tinned copper conductors, stainless steel nuts, and high temperature, fibre reinforced plastics. The units are ignition protected, provide On/Off switching operation, and may be recessed or surface mounted. The remote emergency parallel function can be operated through a momentary button on the dash which will parallel the batteries for 10 minutes. Once this 10 minutes has passed, if the voltage is high enough, the voltage sensitive switch will stay engaged. If not, it will disengage

Features

• Dual battery sensing
  
• Manual override option

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Easy Fit Battery Switch - 275A Continuous

The Easyfit Battery Switch was created for installations where switches need to be recessed through varying thicknesses of panels. It achieves this through an easily removable threaded ring that allows for panel thicknesses up to 3/4" (19 mm). This switch uses the same features as the 701 with the removable key 45 degree past the off position, labeled handle and a removable back cover covering exposed terminals to meet ABYC specifications. It can also be surface mounted offering a unique style compared to other switches available on the market. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory.

Features:

• Can easily be retro-fitted in place of most European post and lever type switches
  
• Molded in high temperature, fiber reinforced plastics
  
• Tin-plated copper studs and nuts
  
• Ignition-protected

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Emergency Parallel Battery Knob, Yellow Easy Fit

This battery knob option for 701 Switches is for applications where emergency parallel switch needs to be highlighted.

• Order separately
  
• Replaces existing knob

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Heavy Duty CB Module, 100A

705 Contour Circuit Breaker HD allows switchable protection for heavy duty circuits like Windlasses or Davit winches utilizing Bussmann Heavy Duty thermal circuit breakers.

• Modular sizing with contour lock moulding allows easy grouping
  
• LED to indicate circuit is on

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Heavy Duty CB Module, 135A

705 Contour Circuit Breaker HD allows switchable protection for heavy duty circuits like Windlasses or Davit winches utilizing Bussmann Heavy Duty thermal circuit breakers.

• Modular sizing with contour lock moulding allows easy grouping
  
• LED to indicate circuit is on

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Heavy Duty CB Module - 50A

705 Contour Circuit Breaker HD allows switchable protection for heavy duty circuits like Windlasses or Davit winches utilizing Bussmann Heavy Duty thermal circuit breakers.

Features:

• Modular sizing with contour lock moulding allows easy grouping
  
• LED to indicate circuit is on

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Heavy-Duty Battery Switch - 600A Continuous

Features:

• The 720 Heavy-duty Battery Switch is well suited to larger vessels, being capable of handling the high electrical loads found on today's boats and
• RV's plus starting large diesel engines
  
• Rated at 600A continuous and 2500A cranking
  
• Can be rear panel, or surface mounted
  
• Uses the same proven style of self cleaning sliding copper contact used inside the 701
  
• Interchangeable labeling system allowing a full range of applications

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Lever-Operated Master Disconnect - ON/OFF

This single pole, single throw switch turns one circuit on and off.

Features:

• Nominal Voltage is 6-36V DC with 175A continuous and 800A intermittent ratings
• Has 3/8" brass terminal studs
• Includes face plate which indicates position of the M284 switch
• 3/4" mounting hole, up to 5/16" panel thickness
• Compares to Cole Hersee part number M-284-09-BP

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Mini Battery Selector Switch

The 701S is the most compact selector switch available on the market. While BEP recommends isolated battery systems as outlined with our distribution clusters, the 701S provides a simple economical way of separating two batteries. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory.

• Housed in the same dimensions as the 701, and includes the same removable side plates and back cover
  
• Please note selector switches will not separate electronics from harmful engine starting spikes
  
• Tin-plated copper studs and nuts
  
• Ignition-protected

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Panel Conversion Kit for ACM to ACSM

BEP's Panel Conversion Kit for ACM to ACSM Includes Mtr .

Panel-Mounted Battery Master Switch

Panel-mounted switches are designed specifically for panel mount applications. This range gives a very compact, versatile solution.

• Compact, lightweight
  
• Removable key
  
• Countersunk recesses for surface mount application
  
• Standard 2-1/16" (52 mm) hole cut out (same as standard gauge hole)
  
• Inside: captive inserts for 3/16" (4.8 mm) nuts providing full access for cables with no restrictions
  
• Standard interchange label system
  
• Molded in high temperature, fiber reinforced plastics

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Panel-Mounted Battery Mini Selector Switch

Panel-mounted switches are designed specifically for panel mount applications. This range gives a very compact, versatile solution.

• Compact, lightweight
  
• Countersunk recesses for surface mount application
  
• Standard 2-1/16" (52 mm) hole cut out (same as standard gauge hole)
  
• Inside: captive inserts for 3/16" (4.8 mm) nuts providing full access for cables with no restrictions
  
• Standard interchange label system
  
• Molded in high temperature, fiber reinforced plastics

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Piezo Buzzer, 30mm 5-30V 85DB

Especially suitable for use with the new 701-MDCZ CZone optimized motorized battery switch, this piezo buzzer is also useful wherever a single tone alarm is required.

• 85 decibel output at 9 Volts
  
• Frequency 3.5KHz
  
• Voltage 5-30 Volts
  
• Power consumption 9mA at 12 Volts

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Bus Bar HD 3 Stud 650A MC5

Pro Installer buss bars are designed for flexibility and scalability. The snap-out side skirts allow for additional cable entry, and radius ends improve cable routing options. it is easy to link other Pro Installer products to the buss bars because of the common interconnection height in the product line.

• Compact footprint saves space
  
• Clear, polycarbonate covers insulate and protect on three sides
  
• Secure cover attachment does not interfere with cabling
  
• Snap-out skirts for flexible cable entry
  
• Radiused ends improve cable routing
  
• Long, threaded studs to connect up to (4) large cable lugs
  
• Plated brass nuts and stainless steel studs prevent thread galling during tightening

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

500A 4 Stud Buss bar

Pro Installer buss bars are designed for flexibility and scalability. The snap-out side skirts allow for additional cable entry, and radius ends improve cable routing options. it is easy to link other Pro Installer products to the buss bars because of the common interconnection height in the product line.

• Compact footprint saves space
  
• Clear, polycarbonate covers insulate and protect on three sides
  
• Secure cover attachment does not interfere with cabling
  
• Snap-out skirts for flexible cable entry
  
• Radiused ends improve cable routing
  
• Long, threaded studs to connect up to (4) large cable lugs
  
• Plated brass nuts and stainless steel studs prevent thread galling during tightening

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A EZ-Mount Dual Bank Control Battery Switch - MC10

Another addition to our multi award winning Pro Installer EZ Mount range, the innovative Dual Bank Control switch is like 3 switches in one, House, Start, and Emergency Parallel. Offering easy intuitive control for the boater, the Dual Bank Control switch features a unique isolated-On position which allows use of house loads and VHF radio if the engine needs to be electrically isolated, or allows the engine to be isolated during servicing while still providing power to house loads (for lighting, stereo, fridge etc). For boats or vehicles with single Engine and House battery bank, Dual Bank Control allows the use of optimized battery banks for their respective loads; an appropriately sized deep cycle bank for House loads, and thin plate starting batteries for the Engine. Further, sensitive electronics are isolated from starter motor induced voltage spikes because House and Engine loads are separated during normal operation, unlike Selector battery switches. As easy as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze.

• Tested to UL1107 ignition protection, CE
  
• Tinned copper 10mm (3/8 inch) studs
  
• Stainless steel washers and nuts
  
• Fiber reinforced plastics
  
• 400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating)
  
• Waterproof to IP67
  
• Same interconnection height as Pro Installer
  
• Removable knob allows isolation during servicing
  
• 3 removable side plates for protection
  
• Industry standard 3.85 x 3.85 inch footprint
  
• For surface mounting only
  
• Each Pro Installer battery switch is fully tested for pressure sealing, rotation force and electrically load tested

Specifications
Mounting: Surface Only
Voltage: 48v DC (for 12-48v systems, both banks must be same voltage)
Rating: 400 Cont / 600 Inter / 1500 Crank
Dims: 3.85" x 3.85" x 3.62"
Operation: 1, 1/2, Parallel, Off
Stud: 4x 10 mm (3.8")

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A EZ-Mount On/Off Battery Switch - MC10

As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front. Never has installation been so easy and cabling so accessible. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. The outstanding performance and features of this powerful new generation battery switch appeal to both the installer and end user. All ratings, footprints and features of the EZ-Mount switch match the high quality of our standard switches.

Features:

• Tested to UL1107 ignition protection, CE
  
• Tinned copper 10mm (3/8") studs
  
• Stainless steel washers/nuts
  
• Fiber reinforced plastics
  
• 400A Continuous / 600A 5 mins Intermittent / 1500A 10 secs Cranking
  
• Waterproof to IP66
  
• Same interconnection height as Pro Installer
  
• Removable knob allows isolation during servicing
  
• 3 removable sideplates for protection
  
• Industry standard 3.85" x 3.85" footprint

Specifications
Mounting: Surface Only
Voltage: 48v DC (for 12-48v systems)
Rating: 400 Cont / 600 Inter / 1500 Crank
Dims: 3.85" x 3.85" x 3.62"
Operation: On/Off
Stud: 2x 10 mm (3.8")

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A Selector w/Field Disconnect Battery Switch - MC10

Power requirements on boats have increased, and these 2 Selector switches offer high power capacity (400 amps continuous), the ability to easily fit doubled cables, and conform to the industry standard mounting footprint (Guest, Perko, Blue Sea). Please note selector switches will not separate electronics from harmful engine starting spikes.

Specifications
Mounting: Surface, Rear or Front
Voltage: 48v DC (for 12-48v systems)
Rating: 400 Cont / 600 Inter / 1500 Crank
Dims: 3.85" x 3.85" x 3.62"
Operation: 1-2-Both-Off
Stud: 3x 10 mm (3.8")

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Busbar HD 5 Stud 650A MC5

Pro Installer buss bars are designed for flexibility and scalability. The snap-out side skirts allow for additional cable entry, and radius ends improve cable routing options. it is easy to link other Pro Installer products to the buss bars because of the common interconnection height in the product line.

• Compact footprint saves space
  
• Clear, polycarbonate covers insulate and protect on three sides
  
• Secure cover attachment does not interfere with cabling
  
• Snap-out skirts for flexible cable entry
  
• Radiused ends improve cable routing
  
• Long, threaded studs to connect up to (4) large cable lugs
  
• Plated brass nuts and stainless steel studs prevent thread galling during tightening

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Busbar HD 8 Stud 650A

Pro Installer buss bars are designed for flexibility and scalability. The snap-out side skirts allow for additional cable entry, and radius ends improve cable routing options. it is easy to link other Pro Installer products to the buss bars because of the common interconnection height in the product line.

• Compact footprint saves space
  
• Clear, polycarbonate covers insulate and protect on three sides
  
• Secure cover attachment does not interfere with cabling
  
• Snap-out skirts for flexible cable entry
  
• Radiused ends improve cable routing
  
• Long, threaded studs to connect up to (4) large cable lugs
  
• Plated brass nuts and stainless steel studs prevent thread galling during tightening

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.